You need to replace the load wheels on your pallet jack.

Your load wheels are worn?

Here are step-by-step instructions on how to replace them.
It's easier than you might think!

Removal of worn load wheels

• Raise forks to full lift height.

• Turn the jack upside down. Here is a video that shows you how to safely turn the jack.

• Remove the load wheel axle fastener using two 3/4" wrenches (LCU) or a 3/8" Allen wrench (CF).

• Slide the load wheel axle out. When removing a badly rusted or damaged axle use a 1/2" pin punch and hammer to drive the axle out.

Always replace both wheels!

Installation of the new wheels

• Install sleeve into load wheel bearing and position washers on sleeve - one on each side of the wheel.

• Place load wheel, sleeve, and washers inside bracket assembly in line with holes in the bracket with sleeve.

• Insert axle through bracket, securing load wheel. Install lock nut and tighten. Same on the other fork.

That's it! You can also watch our step-by-step video on how to replace the load wheels.

Need to order new load wheels? We have a wide selection of different material wheels for most brands of pallet jacks.

And if you need new steer wheels too, order the pre-packaged wheel kits: 

you get the high quality wheels, and the hardware - axles, washers, etc. - comes for free. 

We recommend to have an extra kit on hand as to avoid costly downtime.

Take a look at your shopping cart casters

Are your shopping carts ready?

The fall shopping season is upon us. 

To make sure that you order the correct replacement wheels for your shopping cart, here is a helpful chart to show you the different measurements:

1 Overall Height - The vertical distance between the floor and the mounting plane of the equipment. 

2 Offset - The horizontal distance between vertical center lines through the kingpin and the wheel center. (Not shown in diagram) 

3 Swivel Radius - The horizontal distance from the vertical centerline of the kingpin to the outside edge of the wheel tread. This dimension specifies the minimum distance required for the caster to swivel 360° when mounted. 

4 Wheel Diameter 

5 Tread Width

You can find more information on wheel materials for different surfaces here.

For your convenience, we listed the most commonly used casters for shopping carts:

 

CA 327-A

(5" X 1-1/14" Poly Wheel Assembly used for front & back)

CA 615

(Front swivel caster assembly with 1/2" x 3/4" stem)

 

 

CA A327

(5/16" Diameter Axle Bolt & Nut)

CA RK-1

Shopping Cart Repair Kit* includes:
(10) 5" Front Swivel Casters
(20) 5" Poly-U Wheels
(20) Axles & Locknuts
*All components fit any shopping cart
*Also includes free drill bit for removal of old, worn-out wheels

Order replacement parts at
www.GenericParts.com

Contact us at support@genericparts.com or call (800) 331-0839

Rebuild the hydraulic unit on your Crown PTH50

Your Crown PTH50 pallet jack is not lifting anymore. 

Bleeding it doesn't help, so how do you rebuild the Hydraulic Unit? 

We break the process down into 3 parts:

1) Remove from pallet jack

2) Take the unit apart and drain

3) Rebuild with new seal kit

 Part 1:

How to disassemble a Crown PTH50 Hydraulic Pump

Part 2:

Take the hydraulic unit (Crown PTH50) apart

Part 3:

Rebuild the hydraulic unit (Crown PTH50) with a new seal kit

----------------------------------------------

Get the Crown Seal Kit for your rebuilt,

and any other parts you might need.

Check out over

200,000 new replacement parts for 

 Electric Lift Trucks 

Manual Pallet Jacks 

Industrial Seal Kits 

and more 

Order replacement parts at

www.GenericParts.com

 

Or call our highly knowledgeable customer service staff (800) 331-0839

High Temperature Caster Wheels and Swivel Caster Assemblies

Are you looking for caster wheels for your bakery carts or autoclaves? We have you covered! 

CA CAS-507    Caster wheel

CA CAS-507-S   Swivel caster wheel assembly

Both swivel & rigid caster models are available for a variety of applications on your material handling equipment.

• High-temperature impact resistant epoxy resin
• Non-rusting stainless steel heat resistant yoke
• Precision bearings, available in 5/16" zinc or stainless steel
• Maintenance-free, extended bearing life
• Non-marking wheels for floor protection

Visit our website today!

Follow our blog.

Watch our How-to videos

Log in with your customer number to view net pricing.

 

Or call our highly knowledgeable customer service staff

(800) 331-0839

or email us at csinfo@genericparts.com 

Generic Parts Service is the world's largest supplier of after-market pallet jack parts.

We go the extra mile to make sure you get what you need - fast.

Check out

over 200,000 new replacement parts for

 Electric Lift Trucks  

Manual Pallet Jacks 

LPG Powered Forklifts

Industrial Seal Kits 

and more

Order today at

www.GenericParts.com

Parts for Gravity Conveyors

GRAVITY CONVEYORS

Conveyors have long been an important technology allowing factories,  processors, and warehouses to blossom and grow into the industries we know today.  Since the late 1800’s conveyors are one of the most economical material-handling solutions and have played a major role in increasing efficiency by facilitating the transport of products and goods.  

An unpowered gravity conveyor transports goods and materials with sufficient weight to allow them to move unassisted.  The typical gravity conveyor consists of rows of small rollers or skate-wheels which are mounted in frames generally sloped in a downward, typically on a slightly inclined runway.  Gravity conveyors may be used to move boxes, cartons, and totes with firm bottoms. Roller or skate wheel sizes, as well as spacing, will vary. A good rule of thumb is that a minimum of three rollers must be under the box, carton or tote at all times.

1. NF 016131 - Impact roller
2. NF 016436 - 6” Caster leg w/brake (Square leg Nestaflex 376)
3. NF 016435 - 6” Caster leg, no brake (Square leg Nestaflex 376)
4. NF 006428 - 5” Caster leg, no brake (Round leg Nestaflex 375)
5. NF 003404 - Coupler
6. NF 000047 - Skate wheel
7. NF 017792-001 - Handle kit (Round leg Nestaflex 375)

And many more!

Nestaflex Conveyor Parts 

Best Flex Conveyor Parts 

Aftersort Conveyor Parts

Order replacement parts at

www.GenericParts.com

Log in with your customer number

to view net pricing.

Or call our highly knowledgeable customer service staff at 

(800) 331-0839

Check out over

200,000 new replacement parts for 

Electric Lift Trucks and Manual Pallet Jacks 

Common Replacement Parts for Electric Lift Trucks and Forklilfts

Common Replacement Parts

for Electric Lift Trucks and Forklifts

Tip: Less machine downtime = more productivity, and a better ROI over your equipment's life cycle.

• Have you got a leak? Most common leak points are hoses. Check hoses for cracked rubber and exposed wire structure. Make sure the contact points are properly sealed.  Generic Parts Service carries a huge inventory of hoses, industrial seal kits, and lift truck seal kits. We have kits for the leading manufacturers of pallet jacks, material handling equipment, dump trucks, farming equipment, and logging equipment.

• Are you having travel or lift issues? Check for leaks, cracks, and wear. We have seal kits, mast parts and everything you need to get moving.

• Is your unit was running rough? We carry replacement alternators, vaporizers, radiators, engines, and engine parts.

• Are you having electrical issues, including problems with buttons, switches, pedals or other electrical parts? Make sure wires are not broken or chafe against each other. Switches can mechanically break or corrode. We have a large selection of buttons, boards, switches, wiring harnesses, and pedals as well as many other commonly replaced items.

• How are the brains of the operation? We have replacement control pods, control handles and controllers to help get you moving in the right direction again.

• Are your important safety features, like horns, alarms, and lights in good working order? Some of these wear over time, but most suffer damage. Check your warehouse for obstructions and damage points. Install the accessories inside the overhead guard or within the body of the machine. If broken: We have all of these accessories and more to keep your equipment up to safety standards.

• Are your seatbelts and seats in good working order?  In most cases, the entire seat assembly (seat belt, seat) needs to be replaced to fix the reported issue.  We have aftermarket replacement seats and seat belts for a wide variety of machines.

• How is the condition of your frame and undercarriage? Making sure your frame and undercarriage are in good working order maximizes worker and product safety as well as the working life of your equipment. We have bushings, tension bars, link assemblies, riser assemblies and more to keep you operating safely.

• Have you replaced your batteries but they are still having trouble charging up? Battery life should be roughly 5 years but many factors can influence that. Make sure your battery has enough water and check regularly. We have replacement battery chargers and battery connectors for most brands..

• Have you inspected your wheels lately? Chunked or worn tires or load wheels? We carry wheel kits for most brands of forklifts. Kits include two load wheel assemblies with bearings pressed, along with axles and fasteners.  We also have the drive tires and caster assemblies you need.

Wheel Kits for Manual Pallet Jacks 

Wheel Kits for Electric Lift Trucks

Wheel Kits for High Lift / Scissor Lifts

Need parts? Find them on our website www.genericparts.com

Or call our highly knowledgeable customer service staff (800) 331-0839

Generic Parts Service is the world's largest supplier of after-market pallet jack parts.

We go the extra mile to make sure you get what you need - fast.

ValuJack2 - the best choice pallet jack

• In stock right now
• Cast iron pump with a galvanized finish for superior corrosion resistance and long term reliability

• Poly/steel steer wheels; solid nylon load wheels with options for other wheel materials. 

• Ergonomic rubber grip handle w/3-function hand control and foot release
• Reinforced handle base
• Options are available for backrests and brakes

• Comes with a three-year limited warranty covering manufacturer's defects
• Replacement parts always in stock.

• Protect your feet and order your ValueJack2 with the DuraGuard Toe Guard installed! 

 Call us at 800-331-0839  or email today to order yours. 
                Find more details and specifications on our website.

Generic Parts, Inc.

• Quality replacement parts for electric lift trucks and manual pallet jacks
• Pre-packaged wheel kits for manual  pallet jacks
• Pre-packaged wheel kits for electric lift trucks
• Free online parts catalog with detailed drawings
• Step-by-step How To Videos

www.GenericParts.com