PRE-PACKAGED WHEEL KITS

For easy Pallet Jack and Lift Truck repairs, our pre-packaged wheel kits contain wheels and all the hardware needed to install.

Easy to install 

Compact for Storage

Cost Effective

For Manual Pallet Jacks

For Electric Pallet Jacks

For Scissors Lifts 

Not sure how to replace your wheels and rollers?

We have step-by-step videos that show you how easy it is to

- replace the load wheels

- replace the steer wheels

________________________________________________________

Generic Parts Service is the world's largest supplier 

of after-market pallet jack parts

Check out our replacement parts for

Electric Lift Trucks
Manual Pallet Jacks
Industrial Seal kits 
and more

How-to adjust the handle on your pallet jack

If your pallet jack is not quite working as it should, sometimes a handle adjustment will do the trick.

Tools needed: 

• Hammer
• Philips screwdriver
• Screwdriver
• Pinpunch
• Pliers
• Wrench (10mm)

To adjust the handle on your jack, the first thing you want to do is make sure that the unit is raising. 

First we'll loosen up the 10 millimeter lock nut that's on your adjustment screw, located on the release pedal itself. Then back out the set screw until it no longer touches the release pin. Basically, turn it all the way out. Now the pedal is not contacting anything.

Put the unit to pump position with the lever down, pull the handle down so it's in
pump position, and lightly pump it. The jack is raising now. 

What you want to do then is to is pull the handle lever up into a neutral position and then turn the set screw as you are pumping the handle. And so it's still going up while you keep on turning it. Turn it a little more until it's stopped. At this point, it's in neutral position. 

Now you can take the jam nut, turn it back down, and tighten it back up with the wrench to lock into position. 

Now set your handle lever to "lower" and pump the handle. It should lower the jack. Then set the handle to the neutral position, which shouldn't lower the jack while pumping.

You can watch this process on our 

YouTube channel here.

If you have a question, please give us a call (800)331-0839 

Or send us an email at csinfo@genericparts.com.

Generic Parts has what you need to repair and maintain your material handling equipment.

How much hydraulic fluid?

How much hydraulic fluid is needed to fill the hydraulic unit of a Crown PTH or PTH50?

This hydraulic unit takes about 16 ounces or one pint (about half a liter) of hydraulic fluid.

What you can do is to add the hydraulic fluid right into the unit, just keep adding until the unit is about halfway full without the RAM installed. 
In other words, the fluid level should be about one inch above the seal. Again, if you want to
measure, it's about 16 ounces.

We recommend using Hydraulic fluid Grade AW32 - AW68.

You can watch this here.

If you have a question please give us a call (800)331-0839 

Or send us an email at csinfo@genericparts.com.

Generic Parts has what you need to repair and maintain your material handling equipment.

Let Generic Parts help you identify your pallet jack!

 When it comes time to repair your manual pallet jack, knowing what brand and model you have is crucial. We make it easy to identify your manual pallet jack so you can order the right replacement parts you need to get your jack moving again.

Save yourself valuable time and energy by going through our simple ID process!

1. Take a side-view photo of your pallet jack hydraulic unit

2. Email us at csinfo@genericparts.com or text (503)523-8990 a photo to our helpful customer service team. If you text, be sure to call us right after you send the text. 

One of our friendly customer service representatives will get back to you regarding your specific pallet jack model, along with a parts listing if available. Isn't that easy?!

If you have a question please give us a call (800)331-0839 

Or send us an email at csinfo@genericparts.com.

Generic Parts has what you need to repair and maintain your material handling equipment.

What to do if your pallet jack is not lifting anymore?

 Your Crown PTH50 pallet jack (or a jack with a similar pump) is not lifting anymore.

Your first step is to bleed the pump: 

Put the lever in the release position and pump the handle. About 10 times. That will cycle any air bubbles out of the valve.

If there is still no lifting, check the oil level in the pump. Unscrew the fill plug and check. You should see oil in there, but only to about an inch below the top—not all the way full!

Disconnect the lifting link from the lever and pump the handle: if the pump is lifting, your problem is with the lifting link in the handle. If it is not lifting, your problem is in the pump.

Now you isolated the problem, you can check with us to see if we have a replacement pump or you may decide to rebuild your hydraulic unit with one of our seal kits. 

We have how-to videos to help you.

We break the process down into 3 parts:
1) Remove from pallet jack
2) Take the unit apart and drain
3) Rebuild with new seal kit

 Part 1:

How to disassemble a Crown PTH50 Hydraulic Pump

Part 2:

Take the hydraulic unit (Crown PTH50) apart

Part 3:

Rebuild the hydraulic unit (Crown PTH50) with a new seal kit

Get the Crown Seal Kit for your pump, and any other parts you might need.
 

Order replacement parts at 800-331-0839

www.GenericParts.com